Contact Person : Tiffany
Phone Number : +86 18258386757
WhatsApp : +8618258386757
December 29, 2018
Stainless Steel 316 Ptfe Flocked Kevlar Fabric ptfe Glassfiber Woven Lining Slide Bushing Supplier Manufacture Solutions
VIIPLUS Sliding bearing & bushing PTFE glassfiber Woven lining slide bushing,Bronze Bushings/Sleeve Bushing/Bronze/Bushings Online/Cast Bronze Bushings/Bronze Bushing Manufacturer/Flanged Bronze Bushings/Sleeve Bearings/Bronze Thrust Washers/Sliding Bearing/Self Lubricating Bronze Bushings/Die Components/Polymer Bearings/Self-Lubricated Bearings,made to order from china are the supplier bushings to offer a stainless steel substrate and are among the top performing composite bearings.SST Metal 316 OR 314 Stainless steel and PTFE Flocked Kevlar Fabric incapsulated in Phenolic Resin made in china,Inquiry( Glassfiber lining Slide Bushing)
Steel base TEX PTFE fiber braided self-lubricating bushing,Corrosion-free and maintenance-free material due to stainless steel and PTFE. Outstanding sliding and wear performance.
We Stock and Manufacture Self-lubricating Bearing Solutions for the Pump and Valve Oil & Gas Industries.
Special dimensions and imperial sizes are available on request
Support material:Stainless steel
Intermediate layer:Sintered bronze
Sliding layer:PTFE/Glassfiber Woven Lining Slide Bushing
BUSHING TOLERANCE DETAILS
Bushing inner-Ø after mountingH9
Shaft tolerancef7 or h8
VIIPLUS ptfe fiber metal base self-lubricating bearing is a self-lubricating composite bearing material made of high-quality low-carbon steel plate, bronze plate or stainless steel plate as the matrix, with the woven fabric of ptfe fiber as the friction surface layer. The two are rolled into sliding bearing by means of a solid bond of structural adhesive.In order to guarantee the bonding strength between ptfe fiber and metal sheet, the woven fabric is made of special ptfe filament and aramid filament.The bearing has the characteristics of high bearing capacity, good wear resistance, suitable temperature, wide range of medium, simple structure, compact size and good stability.
Polytetrafluoroethylene (ptfe) is a kind of self-lubricating material with excellent performance.But the wear resistance is poor because of the low strength.At present, most of the fibers or other fillers are used to improve the wear resistance, the effect is very limited.And polytetrafluoroethylene fiber has tensile strength 15 times higher than pure polytetrafluoroethylene resin, to make up for the lack of this aspect, wear resistance is greatly improved, at the same time, the fiber also avoids the occurrence of cold flow phenomenon of polytetrafluoroethylene resin.Polytetrafluoroethylene fiber metal base self-lubricating bearings are divided into steel base, copper base and stainless steel base three.
Polytetrafluoroethylene (PTFE) fiber fabric self-lubricating composite material is a new kind of solid self-lubricating material,PTFE fiber fabric retains the low friction coefficient of PTFE material at the same time, and has a high mechanical strength.Therefore, as the lubrication layer between the inner and outer rings of joint bearing, it is widely used in aerospace, automobile, large machinery and other fields.In this paper, PTFE fiber and Kevlar fiber were used as raw materials to weave PTFE fiber fabric by weaving machine. After the surface treatment of sodium naphthalene complexate solution, the self-lubricating composite material of PTFE fiber fabric was prepared by phenol-epoxy adhesive and bonding curing treatment of 45# steel.The friction coefficient and wear amount of PTFE fiber and the effect of surface treatment on the friction properties of composites were measured by friction and wear testing machine.The friction surface was characterized by scanning electron microscopy and the friction mechanism was analyzed.The interlining materials of woven fabric and finished fabric are compared and analyzed.The results show that the surface treatment with sodium naphthalene complex solution can strip the F element from the surface of PTFE fiber fabric, enhance its bonding strength with metal, but also reduce the wear resistance of PTFE fiber fabric to a certain extent.And the shorter the surface treatment time is, the smaller the reduction of wear resistance will be.In addition, the surface treatment of sodium naphthalene complex solution has little effect on aramid fiber and Kevlar fiber.After surface treatment for 5min, the friction surface of the sample produced more debris and abrasive wear.The higher the content of PTFE fiber in the self-woven fabric, the better the anti-wear performance of the fabric. For the fabric with 30% fiber content, the higher the friction speed is, the higher the friction coefficient is.On the contrary, for fabrics with 80% PTFE fiber content, the higher the friction speed, the lower the friction coefficient.
Stainless steel bushing is maintenance-free bearing material with a PTFE sliding layer, therefore lubrication is not necessary but possible.
Self-lubrication maintenance-free, can work under the condition of complete non-lubrication;
Suitable for rotating, reciprocating, swinging and intermittent motion and other forms of motion;
High carrying capacity, maximum static load up to 210MPa;
Low friction coefficient, oil lubrication to 0.02;
Using a wide temperature range, can be in - 200 ℃ ~ + 250 ℃ temperature range;
Strong impact load resistance, no "crawling" phenomenon, smooth operation;
High wear resistance, good corrosion resistance, no cold flow phenomenon;
Good dimensional stability (no expansion in water), non-conductive, non-magnetic;
Bearing is thin wall structure, light weight, small volume, suitable for compact design;
We are always here to help you.VIIPLU SLEEVE bearings is a premier supplier of high-precision, miniature, and bronze graphite bearings, ptfe pom bearings, bushings, and related bearing services.
ENGINEERING BEARINGS SOLUTIONS
+86-0573-84499350 firstname.lastname@example.org www.bronzegleitlager.com